in this post, I will talk about installing a piezo pickup on my Danelectro DC59. I always kind of wanted a piezo pickup on any of my electric guitars. I noticed that there are bridges with piezo saddles on the market, for Les Pauls and probably for other guitars. But those are not cheap, they're not incredibly expensive, but at the time, I did not want to invest in it.
But now that I got into DIY, things have changed. I came across a video on Youtube (here is a LINK), it explains what a piezo is and how to use it as a contact microphone. It also comes with a schematic for a preamplifier, which I'll show you in another post.
So I decided to build myself a piezo contact microphone and use it on my electric guitars. I bought a medium-sized piezo disc, which I wired as shown in the video above. I placed it on the body of my Danelectro, near the bridge. The sound was garbage and it amplified a lot of unwanted things like me touching the guitar (which was obvious). I tried the same thing with my Les Paul with similar results. Then I tried to place the disc on the headstock, just like you would do with some tuners. Results with the Danelectro were again garbage, but with Les Paul, the sound was actually awesome. But having a piezo disc on your headstock with cables going from it is not exactly pretty. And it still picked up a lot of unwanted sounds.
Then it was obvious that it would have to be placed directly on the bridge. I decided to try it with Danelectro first, because its bridge is a Badass wraparound, with very nice place on the bottom for something like a piezo membrane. Unfortunately, I didn't take a photo of the bridge before placing the piezos inside, but you can google it with ease.
I bought a few piezo discs. It's a thin metal disc, 31mm in diameter, with 18mm of the actual crystal in the center of it. When buying these, watch for these diameters, vendors in my country only show the metal disc diameter, which is kind of useless if you want to cut these metal discs away, like me. For example these 31mm discs have the same sized crystals like the 27mm ones, but those 31s were cheaper for some reason, so I didn't really care.
Then I proceeded to cut these discs to shape, I used three, one was cut on four sides into a rectangle and the other two were cut on three sides, so that there would be that metal overhang on both sides, for soldering a ground wire (which is not really necessary on both sides, but it looks better when it is symmetric, and since the bridge itself is grounded, there is really no need for an extra ground wire coming from the discs). Again, I don't have a photo of the whole pickup before it was put on the bridge, so at least I made this picture:
Picture 1 - Red lines are cuts to make the outer pieces, with the green one to make the center piece, blue and black dots are solder joints. |
When the threes discs were shaped and wires soldered to them, I used epoxy to glue it to the bridge.
Picture 2 - Whole pickup is being held in place while the epoxy hardens. |
Picture 3 - Pickup is finished. |
Picture 4 - Pickup covered with tape. |
Picture 5 - Thin piece of metal to prevent shorting. |
Picture 6 - Tiny hole drilled for the piezo pickup wires. |
Also while the guitar was dismantled, I thought it would be a good idea to shield it better (it was not shielded at all - loud hum). It's usually done with copper tape, but I didn't have it and it's very expensive. Tin foil is a good replacement, secured in place with double-sided tape. In the pictures, it looks very crappy, because it was not easy to place it inside the guitar, but it works like a charm anyway, so that is good enough for me. I also replaced the pickup wires with shielded microphone cables (they are not the same because of the way the Danelectro is wired, the thicker one is stereo, thinner one mono - it looks little bit silly, but I had those cables lying around so why not use them).
Picture 7 |
Picture 8 - Pickguard shielded |
Picture 9 - Insides of the guitar shielded - not pretty, but works flawlessly. The pickup hole and that bridge recess kind of looks like a face doesn't it? :/ |
Picture 10 - Pickup wires replaced by shielded microphone cables, solder joints near the pickups covered with tin foil and tape for maximum shielding. |
So that's it, I hope someone will find this helpful :)
Oh and it wouldn't be complete without a sound sample, so here it is, just a quick recording to give you an idea on how the sound changes from regular magnetic pickups, as you can hear, it's not exactly an acoustic guitar sound, so I'm thinking of building one of those acoustic simulators for it. Recorded using a Fender Mustang.
LINK to Youtube
Nice project may give it a try on my Dano DC59 reissue.....thanks....
ReplyDeleteAlso..might as well make that youtube video public.....nice sound out of your Dano.......
ReplyDeleteCant see the video..please make it avaliable
ReplyDelete